Browse our full catalog organized by medical device category. Each product is manufactured in our ISO 13485-certified, FDA-registered facility with full traceability.
Vital signs acquisition and display electronics for patient monitoring systems.
| Product | Classification | Standards | Lead Time | MOQ | |
|---|---|---|---|---|---|
|
Patient Monitor Mainboard PCBA
Multi-parameter acquisition board supporting ECG (3/5/12-lead), SpO2, NIBP, IBP, temperature, and CO2. Isolated power domains per channel. DSP-based arrhythmia detection.
|
Class II |
|
6-8 weeks | 100 units | Inquire → |
|
Pulse Oximeter Sensor Module
Miniaturized SpO2 board with dual-wavelength LED drivers (660/940nm), high-dynamic-range photodiode amplifier, and motion artifact rejection DSP. Compatible with Nellcor and Masimo protocols.
|
Class II |
|
4-6 weeks | 500 units | Inquire → |
|
ECG Front-End Acquisition Board
12-lead simultaneous acquisition with Wilson central terminal generation, right-leg drive, lead-off detection, and pacemaker pulse rejection. 24-bit ADC, <3 microVpp noise floor.
|
Class II |
|
6-8 weeks | 100 units | Inquire → |
|
Capnography (EtCO2) Sensor Board
Side-stream and main-stream CO2 measurement using NDIR technology. Includes IR source driver, thermopile detector amplifier, and barometric pressure compensation.
|
Class II |
|
8-10 weeks | 200 units | Inquire → |
High-precision analog front-ends and digital processing boards for medical imaging and diagnostic systems.
| Product | Classification | Standards | Lead Time | MOQ | |
|---|---|---|---|---|---|
|
Ultrasound AFE Board (64-Channel)
64-channel transmit/receive analog front-end with integrated T/R switches, LNA, VGA, anti-aliasing filter, and 14-bit ADC per channel. CW Doppler processing support.
|
Class II |
|
8-12 weeks | 50 units | Inquire → |
|
Digital X-Ray Detector Readout Board
Flat-panel detector readout electronics with a-Si TFT array timing control, charge amplifier array interface, and 16-bit ADC pipeline. Gigabit Ethernet image data output.
|
Class II |
|
10-14 weeks | 20 units | Inquire → |
|
MRI Gradient Amplifier Module
High-current, high-slew-rate gradient coil driver with IGBT output stage, real-time current feedback control, and integrated thermal management. 600A peak, 2000V.
|
Class II |
|
12-16 weeks | 10 units | Inquire → |
Control and delivery electronics for active therapeutic medical equipment.
| Product | Classification | Standards | Lead Time | MOQ | |
|---|---|---|---|---|---|
|
Infusion Pump Control Board
Dual-MCU safety architecture with stepper motor driver, occlusion pressure sensing, air-in-line ultrasonic detection, and downstream occlusion monitoring. Free-flow protection.
|
Class II |
|
6-8 weeks | 100 units | Inquire → |
|
Ventilator Main Control Board
Turbine/blower control with FOC motor drive, proportional solenoid valve drivers (O2/Air), differential pressure and flow sensor interfaces (inspiratory/expiratory), and redundant safety MCU.
|
Class IIb |
|
8-10 weeks | 50 units | Inquire → |
|
Defibrillator HV Charge/Discharge Board
High-voltage capacitor charging (up to 5kV), biphasic waveform H-bridge output, patient impedance measurement, and synchronized cardioversion timing. Energy: 1-360J.
|
Class III |
|
10-14 weeks | 25 units | Inquire → |
|
EMS/TENS Therapy Pulse Generator
High-voltage pulse generation (up to 300V), isolated output stage, programmable waveform synthesis (symmetric/asymmetric biphasic, burst, modulated). TENS, NMES, IFC modalities.
|
Class II |
|
6-8 weeks | 200 units | Inquire → |
Miniaturized, low-power electronics for ambulatory and remote patient monitoring.
| Product | Classification | Standards | Lead Time | MOQ | |
|---|---|---|---|---|---|
|
Multi-Sensor Wearable Biosensor Board
Integrated PPG (green/red/IR), bio-impedance (4-wire), skin temperature, and 6-axis IMU. BLE 5.0 connectivity, rechargeable LiPo power management. Rigid-flex construction for wrist/chest wear.
|
Class II |
|
6-8 weeks | 500 units | Inquire → |
|
Continuous Glucose Monitor (CGM) Transmitter
Ultra-low-power potentiostat front-end for enzymatic glucose sensor, NFC/BLE dual-mode wireless, 14-day battery life. Sub-10 microA quiescent current. IP68 sealed assembly.
|
Class II |
|
8-10 weeks | 1000 units | Inquire → |
|
Holter Monitor Recorder Board
3-channel ambulatory ECG recorder with 24/48/72-hour storage, microSD card logging, and USB-C data offload. Medical-grade electrode interface with active noise cancellation.
|
Class II |
|
6-8 weeks | 200 units | Inquire → |
Our engineering team supports your project at every stage — from component engineering and DFM review through to final device packaging and sterilization logistics.
Design-for-manufacturability analysis, BOM scrubbing, component lifecycle verification, and alternate sourcing for long-lifecycle medical products.
Rapid-turn prototypes with full FAIR documentation. IQ/OQ/PQ protocol support for process validation in accordance with ISO 13485.
Automated SMT in certified clean rooms. AOI, X-ray, ICT, and functional test at every station. Full traceability from reel to device.
Device assembly, labelling, IFU insertion, sterilization coordination (EtO/Gamma/E-Beam), and global logistics with regulatory documentation.
Share your device specification, target markets, and volume projections. We return a detailed manufacturing proposal with regulatory pathway guidance.
Submit Your Specification